Washing Machinery
Chinese Wolfberry Cleaning Machine
Relevant technical descriptions of cleaning elution wax machine:
1. Overall dimensions: 8600 * 1450 * 1750 (mm);
2. Vertical vertical support square tube: 60 * 40 * 2.5, horizontal vertical support square tube: 38 * 38 * 2.5; add diagonal support.
3. The thickness of the two circulating water tanks is 2.0mm. The water tank and the rack are not welded, and other items must be bundled during transportation. The height of the water tank is increased by 100mm to 600mm on the basis of the existing prototype. The universal wheel is easy to pull out for cleaning, and a square tube (38X38X2.5) is added in the middle of the bottom shelf of the water tank to facilitate bottom support when the water tank is pulled out.
4. The top of the water tank is equipped with a 40-mesh stainless steel mesh frame and a grid frame with a supporting plate, which is placed on the water tank frame to prevent it from slipping out when it is taken out; the pipe frame of the filter is small, and a filter is added to the water inlet of the pump. Add a net cover at the feed end of the pump;
5. The lower collection tank at the feed end is about 1/3 smaller;
6. The conveying belt adopts a 1000mm stainless steel mesh belt with a pitch of P = 38.1mm, and a string of φ8.0mm. The mesh belt uses wavy guides, a total of five, each with a height of about 10-15mm;
7, the network chain runs smoothly without abnormal noises, and the sealing plate inside the transmission chain cover is more beautiful; the dewaxing liquid and the washing water are circulated back to the water tank without dripping to the outside, and the air flow at the outlet of the dehydration fan is evenly adjustable.
8. The thickness of the dewaxing leaching tank is 1.5MM, and the thickness of the cleaning tank is 2MM.
9. The leaching water is made into a single surface; the leaching water is widened, the level of the leaching box is adjustable, and the angle steel on both sides of the leaching box is welded in turn.
10. There is no leaching box on the conveyor belt slope. The flat section is 3 in front, two dewatering fans, 6 in the back, and 6 hot air dewatering fans. There are three spray pipes on the slope, and a cover is installed above the spray pipes. ?
11. The thickness of the conveyor belt track plate is 3.0mm;
12. The wall panels on both sides are made of 3.0mm thick wire drawing board; the surface of the welding part should be wire drawing.
13. M16 screws are used for the bottom adjustment feet;
14. The height of the inlet is 750mm; add adjusting baffle and spray nozzle.
15. All pipes are bright-faced;
16. The baffles on both sides of the mesh belt are 1.5mm thick.
17. The water collecting tank is lengthened, and the water collecting tank is made easy for cleaning and sanitation;
18. The leaching box is equipped with a quick connector, and the cable uses a stainless steel tube and a terminal block to enter and exit the box.
19. The two water tanks each have two outer wire detection holes with a diameter of 32;
20. The water collecting trough at the discharge opening is 20mm backward at the center of the sprocket;
21, on both sides of the loading material;
22.Unloading mouth and rubber;
23. Rubber is placed on the equalizer, and the leveler is reduced from two to one;
24. Leakage area;
25. The first water pump has two outlets, and the three water tanks can be switched freely;
26. The interface between the circulating water tank and the water pump is made detachable and equipped with calipers;
27. Add heater to the outlet of the rear fan; add the air volume controller to the fan
28. The motor, fan, pump, heater, and power cord are connected to the power terminal box.
29. Transmission network speed, sprocket data: 1:80 (9 meters per minute, 15CM per second)
-
{pboot:if('8600 * 1450 * 1750 (mm)')}
- 8600 * 1450 * 1750 (mm)
外形尺寸 {/pboot:if}
Dimensions: 8600 * 1450 * 1750 (mm);
The machine supports the square tube vertically: 60 * 40 * 2.5, and the horizontal support square pipe: 38 * 38 * 2.5; plus diagonal support.
The thickness of the two circulating water tanks is 2.0mm. The water tank and the rack are not welded, and other items must be bundled during transportation. The height of the water tank is increased by 100mm to 600mm based on the existing prototype.
Two universal wheels are installed on the bottom side of the pump to facilitate cleaning and pulling out, and a square tube (38X38X2.5) is added to the bottom of the water tank to support the bottom when the water tank is pulled out.
Dimensions: 8600 * 1450 * 1750 (mm);
The machine supports the square tube vertically: 60 * 40 * 2.5, and the horizontal support square pipe: 38 * 38 * 2.5; plus diagonal support.
The thickness of the two circulating water tanks is 2.0mm. The water tank and the rack are not welded, and other items must be bundled during transportation. The height of the water tank is increased by 100mm to 600mm based on the existing prototype.
Two universal wheels are installed on the bottom side of the pump to facilitate cleaning and pulling out, and a square tube (38X38X2.5) is added to the bottom of the water tank to support the bottom when the water tank is pulled out.
Relevant technical descriptions of cleaning elution wax machine:
1. Overall dimensions: 8600 * 1450 * 1750 (mm);
2. Vertical vertical support square tube: 60 * 40 * 2.5, horizontal vertical support square tube: 38 * 38 * 2.5; add diagonal support.
3. The thickness of the two circulating water tanks is 2.0mm. The water tank and the rack are not welded, and other items must be bundled during transportation. The height of the water tank is increased by 100mm to 600mm on the basis of the existing prototype. The universal wheel is easy to pull out for cleaning, and a square tube (38X38X2.5) is added in the middle of the bottom shelf of the water tank to facilitate bottom support when the water tank is pulled out.
4. The top of the water tank is equipped with a 40-mesh stainless steel mesh frame and a grid frame with a supporting plate, which is placed on the water tank frame to prevent it from slipping out when it is taken out; the pipe frame of the filter is small, and a filter is added to the water inlet of the pump. Add a net cover at the feed end of the pump;
5. The lower collection tank at the feed end is about 1/3 smaller;
6. The conveying belt adopts a 1000mm stainless steel mesh belt with a pitch of P = 38.1mm, and a string of φ8.0mm. The mesh belt uses wavy guides, a total of five, each with a height of about 10-15mm;
7, the network chain runs smoothly without abnormal noises, and the sealing plate inside the transmission chain cover is more beautiful; the dewaxing liquid and the washing water are circulated back to the water tank without dripping to the outside, and the air flow at the outlet of the dehydration fan is evenly adjustable.
8. The thickness of the dewaxing leaching tank is 1.5MM, and the thickness of the cleaning tank is 2MM.
9. The leaching water is made into a single surface; the leaching water is widened, the level of the leaching box is adjustable, and the angle steel on both sides of the leaching box is welded in turn.
10. There is no leaching box on the conveyor belt slope. The flat section is 3 in front, two dewatering fans, 6 in the back, and 6 hot air dewatering fans. There are three spray pipes on the slope, and a cover is installed above the spray pipes. ?
11. The thickness of the conveyor belt track plate is 3.0mm;
12. The wall panels on both sides are made of 3.0mm thick wire drawing board; the surface of the welding part should be wire drawing.
13. M16 screws are used for the bottom adjustment feet;
14. The height of the inlet is 750mm; add adjusting baffle and spray nozzle.
15. All pipes are bright-faced;
16. The baffles on both sides of the mesh belt are 1.5mm thick.
17. The water collecting tank is lengthened, and the water collecting tank is made easy for cleaning and sanitation;
18. The leaching box is equipped with a quick connector, and the cable uses a stainless steel tube and a terminal block to enter and exit the box.
19. The two water tanks each have two outer wire detection holes with a diameter of 32;
20. The water collecting trough at the discharge opening is 20mm backward at the center of the sprocket;
21, on both sides of the loading material;
22.Unloading mouth and rubber;
23. Rubber is placed on the equalizer, and the leveler is reduced from two to one;
24. Leakage area;
25. The first water pump has two outlets, and the three water tanks can be switched freely;
26. The interface between the circulating water tank and the water pump is made detachable and equipped with calipers;
27. Add heater to the outlet of the rear fan; add the air volume controller to the fan
28. The motor, fan, pump, heater, and power cord are connected to the power terminal box.
29. Transmission network speed, sprocket data: 1:80 (9 meters per minute, 15CM per second)
Chinese Wolfberry Cleaning Machine
-
Brush Roll Peeling and Washing Machine
-
Brush Roll Peeling and Washing Machine
-
Bubble Washing Machine
-
continuous roller foreign boby removal machine
-
Drum Carrot Washing Machine
-
Doubble Network Chain Washing
-
Tumble Bubble Washing Machine
-
Small Vegetable Washing Machine
-
Round Drum Washine Machine
-
Octagonal Brush Drum Washing Machine