Sortering Equipment
LG-380 Metal Detector
Introduction
The device consists of a metal detection head, a conveying rack, a pneumatic component, and a rotating flap. The mixed metal in the food passes through the conveyor belt. Once it enters the metal detection head, the signal light turns on, the buzzer sounds a tweet alarm, and the material together with the mixed metal impurities: 1. Stop on the conveyor belt and be processed manually; 2. The pneumatic component moves through The board rotates and falls into the defective product box below.
Applicable to the detection of iron, stainless steel, aluminum and other metal impurities in dehydrated vegetables, quick-frozen, meat, medicinal materials, clothing, plush toys, etc.
Fourth, failures and troubleshooting methods
(I) The instrument is unstable. Please check the following:
1. Whether the body is well grounded.
2. Is the instrument placed on the floor subject to vibration
3. Whether there are moving metals around the instrument, such as metal trolleys, maintenance tools, operators watches, mobile phones, keys, etc.
(2) Instability caused by the rack, please check the following:
1. Whether the rack adjustment feet are tight and the rack is stable.
2. Whether the rack screws are loose.
3. Whether the conveyor belt rubs the left, right or bottom of the inner wall of the probe.
4. Whether the conveyor belt is contaminated, when the conveyor belt is mixed with metal, it will cause the instrument to alarm periodically.
Five, installation and debugging instructions
(I) Important matters
1. Please read this instruction carefully and completely before using this metal detector.
2. Store this instruction manual. This instruction manual contains important technical matters related to NM-7.
3. The machine has been debugged before leaving the factory. Each time the user starts the machine, the keys on the panel of the host do not need to be adjusted to avoid affecting the detection sensitivity.
(Two) equipment inspection
1. Main detection head. 2. Host. 3. Power controller.
(Three) installation
1. Plug the TX cable into the TX port and the RX cable into the RX port. 2. Plug in the power cord.
(IV) Operation method:
1. Connect the detection head to the TX and RX of the host.
2. Connect the power accessory to the host.
3. Turn on the power switch on the back of the host, and the can work.
4. If the user needs to adjust the sensitivity of the machine, there is a SNTIVITY knob on the back of the machine. Fine-tuning clockwise increases sensitivity; fine-tuning counterclockwise decreases sensitivity.
(V) Precautions
1. This machine uses 220V AC power.
2. Please do not contact the main unit with water (to ensure the safe use of AC power).
3. Do not install this machine in the air outlet.
4. Pay attention not to tear the metal compensation piece in the frame of the detection head.
This series of products are repaired for one year, and lifetime maintenance service.
-
LG-380 Metal Detector
-
LG-380 Metal Detector
-
LG-380 Metal Detector
-
LG-380 Metal Detector
The device consists of a metal detection head, a conveying rack, a pneumatic component, and a rotating flap. The mixed metal in the food passes through the conveyor belt. Once it enters the metal detection head, the signal light turns on, the buzzer sounds a tweet alarm, and the material together with the mixed metal impurities: 1. Stop on the conveyor belt and be processed manually; 2. The pneumatic component moves through the turning The board rotates and falls into the defective product box below.
Applicable to the detection of iron, stainless steel, aluminum and other metal impurities in dehydrated vegetables, quick-frozen, meat, medicinal materials, clothing, plush toys, etc.
Introduction
The device consists of a metal detection head, a conveying rack, a pneumatic component, and a rotating flap. The mixed metal in the food passes through the conveyor belt. Once it enters the metal detection head, the signal light turns on, the buzzer sounds a tweet alarm, and the material together with the mixed metal impurities: 1. Stop on the conveyor belt and be processed manually; 2. The pneumatic component moves through The board rotates and falls into the defective product box below.
Applicable to the detection of iron, stainless steel, aluminum and other metal impurities in dehydrated vegetables, quick-frozen, meat, medicinal materials, clothing, plush toys, etc.
Fourth, failures and troubleshooting methods
(I) The instrument is unstable. Please check the following:
1. Whether the body is well grounded.
2. Is the instrument placed on the floor subject to vibration
3. Whether there are moving metals around the instrument, such as metal trolleys, maintenance tools, operators watches, mobile phones, keys, etc.
(2) Instability caused by the rack, please check the following:
1. Whether the rack adjustment feet are tight and the rack is stable.
2. Whether the rack screws are loose.
3. Whether the conveyor belt rubs the left, right or bottom of the inner wall of the probe.
4. Whether the conveyor belt is contaminated, when the conveyor belt is mixed with metal, it will cause the instrument to alarm periodically.
Five, installation and debugging instructions
(I) Important matters
1. Please read this instruction carefully and completely before using this metal detector.
2. Store this instruction manual. This instruction manual contains important technical matters related to NM-7.
3. The machine has been debugged before leaving the factory. Each time the user starts the machine, the keys on the panel of the host do not need to be adjusted to avoid affecting the detection sensitivity.
(Two) equipment inspection
1. Main detection head. 2. Host. 3. Power controller.
(Three) installation
1. Plug the TX cable into the TX port and the RX cable into the RX port. 2. Plug in the power cord.
(IV) Operation method:
1. Connect the detection head to the TX and RX of the host.
2. Connect the power accessory to the host.
3. Turn on the power switch on the back of the host, and the can work.
4. If the user needs to adjust the sensitivity of the machine, there is a SNTIVITY knob on the back of the machine. Fine-tuning clockwise increases sensitivity; fine-tuning counterclockwise decreases sensitivity.
(V) Precautions
1. This machine uses 220V AC power.
2. Please do not contact the main unit with water (to ensure the safe use of AC power).
3. Do not install this machine in the air outlet.
4. Pay attention not to tear the metal compensation piece in the frame of the detection head.
This series of products are repaired for one year, and lifetime maintenance service.
LG-380 Metal Detector
-
Magnetic vibration sieve winnowing machine
-
Through Magnetic Machine
-
Stem and Leaf Winnowing Machine
-
LG-380 Metal Detector
-
ND150 Winch Hoister
-
Lips Hoister
-
Hoister
-
Plate chain Hoister
-
Circular Conveyor
-
Packaging conveyor